Bryant TSTATBBN2S01-C Manuel d'installation télécharger pdf (Page 13)

Page 13

ELECTRICAL-LINE VOLTAGE

All ﬁ eld installed wiring, including electrical ground,

must comply with the National Electrical Code as well as

all applicable local codes.

Refer to the unit wiring diagrams for fuse sizes and a

schematic of the ﬁ eld connections which must be made by

the installing (or electrical) contractor.

Consult the unit wiring diagram located on the inside of the

compressor access panel to ensure proper electrical hookup.

All ﬁ nal electrical connections must be made with a

length of ﬂ exible conduit to minimize vibration and sound

transmission to the building.

To avoid possible injury or death due to

electrical shock, open the power supply

disconnect switch and secure it in an open

position during installation.

CAUTION: Use only copper conductors for ﬁ eld

installed electrical wiring. Unit terminals are not

designed to accept other types of conductors.

Figure 17. Line Voltage Field Wiring

Table 5. Electrical Data

General Line Voltage Wiring

Be sure the available power is the same voltage and phase

as that shown on the unit serial plate. Line and low voltage

wiring must be done in accordance with local codes or the

National Electric Code, whichever is applicable.

Unit Power Connection

Line voltage connection is made by connecting the

incoming line voltage wires to the “L” side of the

contactor as shown in Figure 16. Consult Table 5 for

correct wire and fuse size.

External Loop Power Connection

If the unit is to be used with an external loop pump, the

pump(s) will be connected to the loop pump terminals in

the unit electrical box as shown in Figure 17. The pumps

will automatically be cycled as required by the unit.

208 Volt Operation

All 208-230 volt units are factory wired for 230 volt.

The transformers may be switched to 208V operation as

illustrated on the wiring diagram.

HWG Pumping Wiring

Install HWG Pump power wires on HWG Pump power

block after insuring water is in HWG circuit.

Fan Fan HWG Loop Total Minimum Max Max Min Maximum

Model Motor Motor Pump Pump FLA Circuit Fuse Fuse Wire Wire

RLA LRA RLA LRA HP FLA Amps Amps Amps Ampacity USA Can AWG Length (ft.)

036 7.1 38 7.1 38 1/2 4.3 0.4 4.0 22.9 24.7 30 30 10 70

042 10.0 42 10.7 47 1/2 4.3 0.4 4.0 29.4 32.1 40 40 8 90

048 10.7 47 11.4 54 1.0 7.0 0.4 4.0 33.5 36.3 45 45 6 120

060 13.6 67 13.6 67 1.0 7.0 0.4 4.0 38.6 42.0 50 50 6 110

072 15.0 73 15.0 73 1.0 7.0 0.4 4.0 41.4 45.2 50 50 6 100

Rev.: 03/30/01B

All units rated Voltage of 208-230/60/1.

All units Min/Max Voltage of 187/253.

HACR breaker in USA only. All fuses Class RK-5.

Wire length based on one way measurement with 2% Voltage drop and wire size based upon 60°C copper conductors.

Compressor

Sys A Sys B

Transformer

Compressor A

Contactor

208-230/60/1

4 Amp Max.

Source Pump

Ground

ICM2

Controller

Pump

Circt Brkr

with ground

(see Elect. Table for wire

and Brkr. size)

Compressor B

Contactor

CXM Control - A

Low Voltage

Connector

CXM Control - B

Low Voltage

Connector

HWG

Install HWG Pump

Power after insuring

water is in HWG circuit

Yellow

Blk

External Loop Pump(s)

WARNING

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Bryant TSTATBBN2S01-C Manuel d'installation Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Thermostats Bryant TSTATBBN2S01-C