Bryant start--up operating and service and Manuel d'instructions Page 51
- Page / 86
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
51
VENT PIPE FLUSH SHOWING COUPLING
VENT PIPE FLUSH WITH ADAPTER
VENT PIPE ADAPTER WITH GASKET
INSTALLED ON FURNACE VENT
PIPE IS CUT FLUSH WITH TOP OF
ADAPTER.
ALIGN NOTCHES IN VENT PIPE
COUPLING OVER STAND-OFF
ON ADAPTER. TORQUE LOWER
CLAMP 15 LB-IN. WHEN REMAINING
VENT PIPE IS INSTALLED, TORQUE
UPPER CLAMP TO 15 LB-IN.
A11339
Fig. 42 -- Vent Pipe Flush with Adaptor
12” MINIMUM
256.0 mm
TOP PLATE ATTACHMENT
COMBUSTION AIR PIPE
(ATTIC OR CRAWLSPACE ONLY)
CASING SIDE ATTACHMENT
COMBUSTION AIR PIPE
(ATTIC OR CRAWLSPACE ONLY)
Point elbow down towards
back of furnace
A11376
Fig. 43 -- Combustion Air Pipe Attachment
987MA
- Always Ask For 1
- IMPORTANT 2
- SAFETY CONSIDERATIONS 3
- INTRODUCTION 4
- CODES AND STANDARDS 4
- ELECTROSTATIC DISCHARGE (ESD) 4
- PRECAUTIONS PROCEDURE 4
- ACCESSORIES 5
- LOCATION 5
- * Recommended 6
- Fig. 1 -- Dimensional Drawing 7
- SUPPLY AIR 8
- 18-IN. (457.2 mm) 8
- MINIMUM TO BURNERS 8
- AIR FOR COMBUSTION AND 9
- VENTILATION 9
- CONDENSATE TRAP 11
- (Appearance May Vary) 13
- CONDENSATE DRAIN CONNECTION 16
- Remove knockout 17
- Install grommet before 17
- INSTALLATION 18
- Horizontal Installation 19
- Filter Arrangement 19
- Fig. 17 -- Media Filter 21
- UPFLOW DOWNFLOW HORIZONTAL 23
- HORIZONTAL TOP 24
- RETURN NOT 24
- PERMITTED FOR 24
- ANY MODEL 24
- COMBUSTION - AIR PIPE 25
- (SEE VENTING SECTION) 25
- AIR DUCTS 26
- GAS PIPING 29
- ELECTRICAL CONNECTIONS 30
- J--Box Installation 31
- 24--V Wiring 31
- Alternate Power Supplies 32
- 12 and 16 36
- Materials 39
- Venting Systems 39
- Locating the Vent Termination 39
- Guidelines 40
- Configure the Furnace 40
- Pipe Adapter 41
- Roof Terminations 41
- Vent Coupling and Adapter 46
- Downflow Vertical 48
- HORIZONTAL LEFT 49
- RIGHT VENT CONFIGURATION* 49
- Fig. 41 -- Horizontal Right 50
- TOP PLATE ATTACHMENT 51
- COMBUSTION AIR PIPE 51
- (ATTIC OR CRAWLSPACE ONLY) 51
- Abandoned masonry 54
- (per code) 54
- OVERHANG 55
- 12 in. (304.8mm) MIN. Ground 55
- Level OR Snow Level 55
- Select Setup Switch Positions 57
- Purge Gas Lines 57
- Adjustments 58
- Adjust Temperature Rise 59
- MODULATING 61
- 338307-2 Rev. C 62
- A11365 AMV98 63
- MODULATING FURNACE 65
- U.S.A. Only 66
- SERVICE AND MAINTENANCE 67
- PROCEDURES 67
- Component Self--Test 68
- Care and Maintenance 68
- Servicing Hot Surface Igniter 71
- WINTERIZATION 72
- Burner Flame 73
- Manifold 73
- Fig. 60 -- Blower Assembly 74
- Fig. 61 -- Burner Assembly 75
- Troubleshootin 76
- SEQUENCE OF OPERATION 79
- Maximum Heating 81
- Cooling Mode 81
- Super Dehumidify Mode 82
- Continuous Blower Mode 82
- Heat Pump 83
- Component Self Test 83
- Catalog No. II987M 86
Produits connexes et manuels pour Pompes à chaleur Bryant start--up operating and service and
(36 pages)
(28 pages)Messer Cutting & Welding Sicherheitszugriffskontrollsysteme Benutzerhandbücher
Die Liste der Messer Cutting & Welding Sicherheitszugriffskontrollsysteme -Produkte enthält 2 Benutzerhandbücher für 2 diese Modelle. Alle PDF-Benutzerhandbücher können heruntergeladen oder online angezeigt werden.
Commentaires sur ces manuels