Bryant BS2 Manuel d'utilisateur télécharger pdf

BS2

Product Data

G A S --- F I R E D S T E A M B O I L E R

A12465

Fig. 1 -- Model BS2

C US

Use of the AHRI Certified TM Mark indicates a

manufacturer’s participation in the program. For

verification of certification for individual products,

go to www.ahridirectory.org.

This Model BS2 Gas--Fired Steam Boiler provides fast heat quietly

and economically to assure the finest in hydronic heating.

This boiler provides quality design in a small, compact unit easily

installed in a basement, garage, or utility room. It can be installed

on a combustible floor when an optional combustible floor base is

used.

The BS2 boiler is CSA certified for use with natural gas and is

field convertible for use with propane gas when a

factory--authorized conversion kit is used.

FEATURES

Range of Capacities—These boilers are available in sizes 75,000

through 299,000 BTUH.

Completely Packaged—Each boiler is completely assembled,

including all controls (except room thermostat). All necessary

wiring is factory installed. The boiler is ready for gas, water, room

thermostat, and electrical connections as shipped.

Thermal--Pin, Cast--Iron Sections—These sections speed heat

transfer from the flue gases to the boiler water with faster

thermostat response, providing greater comfort and economy.

Maximum heat is produced at a lower level on the thermal--pin

sections, leading to peak efficiency. Steel push nipples are used

between each section to provide a water--tight seal.

Integral Draft—These boilers incorporate an integral draft system

to simplify installation. No external draft diverter is needed.

Titanium Composite Burners—Provide quiet operation,

corrosion resistance and improved combustion efficiency. Propane

convertible with accessory kit.

Controls—An automatic gas valve and intermittent pilot provide

quiet dependable operation of the burners. Factory--supplied safety

components assure protection against overheating, pressure

build--up and low--water operation.

Insulated Casing—The casing is fully insulated with fiberglass for

maximum operating efficiency and economy.

Automatic Vent Damper—The BS2 boiler is CSA design

certified for use with a factory--supplied automatic vent damper.

This boiler is Category 1 for venting purposes.

Sections Tested—Each section is hydrostatically tested to 50 psig.

Individual sections are tested to 125 psig at factory. Assembled

sections are tested to 75 psig at the factory. Maximum allowable

working pressure is 50 psig. The maximum allowable pressure is

15 psig for steam boilers.

1 2 3 4

Résumé du contenu

Page 1 - Product Data

BS2Product DataG A S --- F I R E D S T E A M B O I L E RA12465Fig. 1 -- Model BS2C USUse of the AHRI Certified TM Mark indicates a manufactu

Page 2 - BOILER ACCESSORIES

2MODEL NUMBER NOMENCLATUREBS2 AAN000042A A AA B — BoilerCoolingVariationsAA — StandardType of SystemS — SteamSeriesA i— OriginalCombustion/Ignition2 —

Page 3 - SPECIFICATIONS

3DIMENSIONSA12466CLEARANCES -- IN. (MM)PART OF BOILER CLEARANCERight Side 3 (76 mm)*Left Side (Control Side) 9 (229 mm)Top 18 (457 mm)Back 8 (203 mm)F

Page 4 - ELECTRICAL DATA

4ELECTRICAL DATAALL MODELSVoltage—Hertz—Phase 115 — 60 — 1Minimum Branch Circuit Wire Size (AWG) 14MaximumFuseSize(Amps) 15Control Circuit Power Avail

Commentaires sur ces manuels

Pas de commentaire

Bryant BS2 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Chauffe-eau et chaudières Bryant BS2. SS-BS2-01 - County Heating & Air Conditioning Inc Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Chauffe-eau et chaudières Bryant BS2